Improve Your Knowledge with NSE5_FAZ-7.2 Exam Dumps

Category:

Comments:

0 Comments

Post Date:

August 8, 2023

Practicing with NSE5_FAZ-7.2 questions can help you identify areas where you need to improve your knowledge. By answering NSE5_FAZ-7.2 questions and reviewing your responses, you can identify gaps in your understanding and focus your study efforts on those areas. The NSE5_FAZ-7.2 exam has a strict time limit, and you need to manage your time effectively to answer all the questions. Practicing with Fortinet NSE5_FAZ-7.2 dumps questions can help you develop time management skills by simulating the exam's time constraints. You'll learn how to pace yourself, manage your time effectively, and ensure that you complete the NSE5_FAZ-7.2 exam within the allotted time. Test Fortinet NSE5_FAZ-7.2 exam free dumps below.

Page 1 of 5

1. What is the recommended method of expanding disk space on a FortiAnalyzer VM?

From the VM host manager, add an additional virtual disk and use the #execute lvm extend command to expand the storage

From the VM host manager, expand the size of the existing virtual disk

From the VM host manager, expand the size of the existing virtual disk and use the # execute format disk command to reformat the disk

From the VM host manager, add an additional virtual disk and rebuild your RAID array

2. What is the purpose of employing RAID with FortiAnalyzer?

To introduce redundancy to your log data

To provide data separation between ADOMs

To separate analytical and archive data

To back up your logs

3. An administrator has configured the following settings:

config system fortiview settings

set resolve-ip enable

end

What is the significance of executing this command?

Use this command only if the source IP addresses are not resolved on FortiGate.

It resolves the source and destination IP addresses to a hostname in FortiView on FortiAnalyzer.

You must configure local DNS servers on FortiGate for this command to resolve IP addresses on Forti Analyzer.

It resolves the destination IP address to a hostname in FortiView on FortiAnalyzer.

4. What happens when the IOC breach detection engine on FortiAnalyzer finds web logs that match a blocklisted IP address?

The endpoint is marked as Compromised and. optionally, can be put in quarantine.

FortiAnalyzer flags the associated host for further analysis.

A new Infected entry is added for the corresponding endpoint.

The detection engine classifies those logs as Suspicious

5. Which two settings must you configure on FortiAnalyzer to allow non-local administrators to authenticate to FortiAnalyzer with any user account in a single LDAP group? (Choose two.)

A local wildcard administrator account

A remote LDAP server

A trusted host profile that restricts access to the LDAP group

An administrator group

6. Refer to the exhibit.

What is the purpose of using the Chart Builder feature on FortiAnalyzer?

To add a new chart under FortiView to be used in new reports

To build a dataset and chart automatically, based on the filtered search results

To add charts directly to generate reports in the current ADOM

To build a chart automatically based on the top 100 log entries

7. How can you configure FortiAnalyzer to permit administrator logins from only specific locations?

Use static routes

Use administrative profiles

Use trusted hosts

Use secure protocols

8. For which two SAML roles can the FortiAnalyzer be configured? (Choose two.)

Principal

Service provider

Identity collector

Identity provider

9. Refer to the exhibit.

The image displays the configuration of a FortiAnalyzer the administrator wants to join to an existing HA cluster.

What can you conclude from the configuration displayed?

This FortiAnalyzer will join to the existing HA cluster as the primary.

This FortiAnalyzer is configured to receive logs in its port1.

This FortiAnalyzer will trigger a failover after losing communication with its peers for 10 seconds.

After joining to the cluster, this FortiAnalyzer will keep an updated log database.

10. Logs are being deleted from one of the ADOMs earlier than the configured setting for archiving in the data policy.

What is the most likely problem?

CPU resources are too high

Logs in that ADOM are being forwarded, in real-time, to another FortiAnalyzer device

The total disk space is insufficient and you need to add other disk

The ADOM disk quota is set too low, based on log rates

Page 2 of 5

11. What are analytics logs on FortiAnalyzer?

Log type Traffic logs.

Logs that roll over when the log file reaches a specific size.

Logs that are indexed and stored in the SQ

Raw logs that are compressed and saved to a log file.

12. How do you restrict an administrator’s access to a subset of your organization’s ADOMs?

Set the ADOM mode to Advanced

Assign the ADOMs to the administrator’s account

Configure trusted hosts

Assign the default Super_User administrator profile

13. Which tabs do not appear when FortiAnalyzer is operating in Collector mode?

FortiView

Event Management

Device Manger

Reporting

14. If the primary FortiAnalyzer in an HA cluster fails, how is the new primary elected?

The configured IP address is checked first.

The active port number is checked first.

The firmware version is checked first.

The configured priority is checked first

15. Which two statements are true regarding FortiAnalyzer log forwarding? (Choose two.)

Both modes, forwarding and aggregation, support encryption of logs between devices.

In aggregation mode, you can forward logs to syslog and CEF servers as well.

Aggregation mode stores logs and content files and uploads them to another FortiAnalyzer device at a scheduled time.

Forwarding mode forwards logs in real time only to other FortiAnalyzer devices.

16. View the exhibit:

What does the 1000MB maximum for disk utilization refer to?

The disk quota for the FortiAnalyzer model

The disk quota for all devices in the ADOM

The disk quota for each device in the ADOM

The disk quota for the ADOM type

17. FortiAnalyzer reports are dropping analytical data from 15 days ago, even though the data policy setting for analytics logs is 60 days.

What is the most likely problem?

Quota enforcement is acting on analytical data before a report is complete

Logs are rolling before the report is run

CPU resources are too high

Disk utilization for archive logs is set for 15 days

18. Which statement describes a dataset in FortiAnalyzer?

They determine what data is retrieved from the database.

They provide the layout used for reports.

They are used to set the data included in templates.

They define the chart types to be used in reports.

19. What can you do on FortiAnalyzer to restrict administrative access from specific locations?

Configure trusted hosts for that administrator.

Enable geo-location services on accessible interface.

Configure two-factor authentication with a remote RADIUS server.

Configure an ADOM for respective location.

20. A playbook contains five tasks in total. An administrator runs the playbook and four out of five tasks finish successfully, but one task fails.

What will be the status of the playbook after it is run?

Running

Failed

Upstream_failed

Success

Page 3 of 5

21. For which two purposes would you use the command set log checksum? (Choose two.)

To help protect against man-in-the-middle attacks during log upload from FortiAnalyzer to an SFTP server

To prevent log modification or tampering

To encrypt log communications

To send an identical set of logs to a second logging server

22. Which two methods can you use to send event notifications when an event occurs that matches a configured event handler? (Choose two.)

SMS

SNMP

23. A play book contains five tasks in total. An administrator executed the playbook and four out of five tasks finished successfully, but one task failed.

What will be the status of the playbook after its execution?

Success

Failed

Running

Upstream_failed

24. View the exhibit.

What does the data point at 14:35 tell you?

FortiAnalyzer is dropping logs.

FortiAnalyzer is indexing logs faster than logs are being received.

FortiAnalyzer has temporarily stopped receiving logs so older logs’ can be indexed.

The sqlplugind daemon is ahead in indexing by one log.

25. What is required to authorize a FortiGate on FortiAnalyzer using Fabric authorization?

A FortiGate ADOM

The FortiGate serial number

A pre-shared key

Valid FortiAnalyzer credentials

26. On FortiAnalyzer, what is a wildcard administrator account?

An account that permits access to members of an LDAP group

An account that allows guest access with read-only privileges

An account that requires two-factor authentication

An account that validates against any user account on a FortiAuthenticator

27. What statements are true regarding the "store and upload" log transfer option between FortiAnalyzer and FortiGate? (Choose three.)

All FortiGates can send logs to FortiAnalyzer using the store and upload option.

Only FortiGate models with hard disks can send logs to FortiAnalyzer using the store and upload option.

Both secure communications methods (SSL and IPsec) allow the store and upload option.

Disk logging is enabled on the FortiGate through the CLI only.

Disk logging is enabled by default on the FortiGate.

28. What does the disk status Degraded mean for RAID management?

One or more drives are missing from the FortiAnalyzer unit. The drive is no longer available to the operating system.

The FortiAnalyzer device is writing to all the hard drives on the device in order to make the array fault tolerant.

The FortiAnalyzer device is writing data to a newly added hard drive in order to restore the hard drive to an optimal state.

The hard driveiIs no longer being used by the RAID controller

29. What are two effects of enabling auto-cache in a FortiAnalyzer report? (Choose two.)

The size of newly generated reports is optimized to conserve disk space.

FortiAnalyzer local cache is used to store generated reports.

When new logs are received, the hard-cache data is updated automatically.

The generation time for reports is decreased.

30. What is the purpose of a dataset query in FortiAnalyzer?

It sorts log data into tables

It extracts the database schema

It retrieves log data from the database

It injects log data into the database

Page 4 of 5

31. An administrator has moved FortiGate A from the root ADOM to ADOM1.

Which two statements are true regarding logs? (Choose two.)

Analytics logs will be moved to ADOM1 from the root ADOM automatically.

Archived logs will be moved to ADOM1 from the root ADOM automatically.

Logs will be presented in both ADOMs immediately after the move.

Analytics logs will be moved to ADOM1 from the root ADOM after you rebuild the ADOM1 SQL database.

32. On the RAID management page, the disk status is listed as Initializing.

What does the status Initializing indicate about what the FortiAnalyzer is currently doing?

FortiAnalyzer is ensuring that the parity data of a redundant drive is valid

FortiAnalyzer is writing data to a newly added hard drive to restore it to an optimal state

FortiAnalyzer is writing to all of its hard drives to make the array fault tolerant

FortiAnalyzer is functioning normally

33. Logs are being deleted from one of your ADOMs earlier that the configured setting for archiving in your data policy.

What is the most likely problem?

The total disk space is insufficient and you need to add other disk.

CPU resources are too high.

The ADOM disk quota is set too low based on log rates.

Logs in that ADOM are being forwarded in real-time to another FortiAnalyzer device.

34. You are using RAID with a FortiAnalyzer that supports software RAID, and one of the hard disks on FortiAnalyzer has failed.

What is the recommended method to replace the disk?

Shut down FortiAnalyzer and then replace the disk

Downgrade your RAID level, replace the disk, and then upgrade your RAID level

Clear all RAID alarms and replace the disk while FortiAnalyzer is still running

Perform a hot swap

35. When working with FortiAnalyzer reports, what is the purpose of a dataset?

To provide the layout used for reports

To define the chart type to be used

To retrieve data from the database

To set the data included in templates

36. Why run the command diagnose sql status sqlplugind?

To list the current SQL processes running

To check what is the database log insertion status

To display the SOL query connections and hcache status

To view the current hcache size

37. What happens when a log file saved on FortiAnalyzer disks reaches the size specified in the device log

settings?

The log file is stored as a raw log and is available for analytic support.

The log file rolls over and is archived.

The log file is purged from the database.

The log file is overwritten.

38. Which statements are correct regarding FortiAnalyzer reports? (Choose two)

FortiAnalyzer provides the ability to create custom reports.

FortiAnalyzer glows you to schedule reports to run.

FortiAnalyzer includes pre-defined reports only.

FortiAnalyzer allows reporting for FortiGate devices only.

39. What are two benefits of using fabric connectors? (Choose two.)

They allow FortiAnalyzer to send logs in real-time to public cloud accounts.

You do not need an additional license to send logs to the cloud platform.

Fabric connectors allow you to improve redundancy.

Using fabric connectors is more efficient than using third-party polling with AP

40. Which statement is true when you are upgrading the firmware on an HA cluster made up of two FortiAnalyzer devices?

First, upgrade the secondary device, and then upgrade the primary device.

Both FortiAnalyzer devices will be upgraded at the same time.

You can enable uninterruptible-upgrade so that the normal FortiAnalyzer operations are not interrupted while the cluster firmware upgrades.

You can perform the firmware upgrade using only a console connection.

Page 5 of 5

41. An administrator has moved FortiGate A from the root ADOM to ADOM1. However, the administrator is not able to generate reports for FortiGate A in ADOM1.

What should the administrator do to solve this issue?

Use the execute sql-local rebuild-db command to rebuild all ADOM databases.

Use the execute sql-local rebuild-adom ADOM1 command to rebuild the ADOM database.

Use the execute sql-report run ADOM1 command to run a report.

Use the execute sql-local rebuild-adom root command to rebuild the ADOM database.

TAGS:

NSE5_FAZ-7.2, NSE5_FAZ-7.2 exam dumps

Notify of

Label

Name*

Email*

Website

Label

Name*

Email*

Website

0 Comments

Oldest

Newest Most Voted

Inline Feedbacks

View all comments

Get NSE5_FAZ-7.2 Dumps Full Version

Q&As: 137
Versions: PDF and Software Download Now

About Dumpsinfo

Dumpsinfo is a good platform providing the latest exam information and dumps questions for all IT certification exams. You can study all the latest exam dumps questions online.

[email protected]

Mon - Sat 9:00am - 6:00pm

Improve Your Knowledge with NSE5_FAZ-7.2 Exam Dumps

Related

Posts

FCP_ZCS_AD-7.4 Dumps Help You Study Objectives

Improve Your Knowledge with FCSS_NST_SE-7.4 Exam Dumps

Online FCP_FAZ_AD-7.4 Dumps Help You Understand Questions Well

FCP_FAZ_AN-7.4 Dumps Questions Increase Your Chance of Success

About Us

EMAIL

Services

Opening Hours