Prepare NSE6_FNC-7.2 Exam with Using NSE6_FNC-7.2 Dump Questions

If you are serious about passing your Fortinet NSE6_FNC-7.2 certification exam, practicing with NSE6_FNC-7.2 dumps questions is an essential step in your preparation process. These NSE6_FNC-7.2 dumps will help you assess your knowledge, identify your strengths and weaknesses, and improve your chances of passing the exam on the first try. So why wait? Start practicing today and give yourself the best possible chance of success! Test free NSE6_FNC-7.2 exam dumps questions below.

Page 1 of 2

1. View the command and output shown in the exhibit.





What is the current state of this host?

Rogue

Registered

Not authenticated

At-Risk

 Loading...

2. Which agent can receive and display messages from FortiNAC to the end user?

Dissolvable

Persistent

Passive

MDM

 Loading...

3. During the on-boarding process through the captive portal, what are two reasons why a host that successfully registered would remain stuck in the Registration VLAN? (Choose two.)

The wrong agent is installed.

The port default VLAN is the same as the Registration VLA

Bridging is enabled on the host.

There is another unregistered host on the same port.

 Loading...

4. What would happen if a port was placed in both the Forced Registration and the Forced Remediation port groups?

Only rogue hosts would be impacted.

Both enforcement groups cannot contain the same port.

Only al-risk hosts would be impacted.

Both types of enforcement would be applied.

 Loading...

5. While troubleshooting a network connectivity issue, an administrator determines that a device was being automatically provisioned to an incorrect VLAN.

Where would the administrator look to determine when and why FortiNAC made the network access change?

The Event view

The Admin Auditing view

The Port Changes view

The Connections view

 Loading...

6. Which agent is used only as part of a login script?

Mobile

Passive

Persistent

Dissolvable

 Loading...

7. 1.Where should you configure MAC notification traps on a supported switch?

Configure them only after you configure linkup and linkdown traps.

Configure them on all ports on the switch.

Configure them only on ports set as 802 1g trunks.

Configure them on all ports except uplink ports.

 Loading...

8. Which three circumstances trigger Layer 2 polling of infrastructure devices? (Choose three.)

Manual polling

Scheduled poll timings

A failed Layer 3 poll

A matched security policy

Linkup and Linkdown traps

 Loading...

9. Which connecting endpoints are evaluated against all enabled device profiling rules?

All hosts, each time they connect

Rogues devices, only when they connect for the first time

Known trusted devices each time they change location

Rogues devices, each time they connect

 Loading...

10. When you create a user or host profile; which three criteria can you use? (Choose three.)

An applied access policy

Administrative group membership

Location

Host or user group memberships

Host or user attributes

 Loading...

Page 2 of 2

11. Which group type can have members added directly from the FortiNAC Control Manager?

Administrator

Device

Port

Host

 Loading...

12. Which two policy types can be created on a FortiNAC Control Manager? (Choose two.)

Authentication

Network Access

Endpoint Compliance

Supplicant EasvConnect

 Loading...

13. By default, if after a successful Layer 2 poll, more than 20 endpoints are seen connected on a single switch port simultaneously, what happens to the port?

The port becomes a threshold uplink

The port is disabled

The port is added to the Forced Registration group

The port is switched into the Dead-End VLAN

 Loading...

14. Which two agents can validate endpoint compliance transparently to the end user? (Choose two.)

Dissolvable

Mobile

Passive

Persistent

 Loading...

15. How are logical networks assigned to endpoints?

Through device profiling rules

Through network access policies

Through Layer 3 polling configurations

Through FortiGate IPv4 policies

 Loading...

 Loading...