D-PCM-DY-23 Exam Dumps - Reliable Way to Pass and Get Certified

D-PCM-DY-23 Exam Dumps – Reliable Way to Pass and Get Certified

Category:

Comments:

0 Comments

Post Date:

March 31, 2024

If you are looking for a reliable and comprehensive way to prepare for your D-PCM-DY-23 certification exam, look no further than D-PCM-DY-23 exam questions. These D-PCM-DY-23 exam dumps questions are designed to help you assess your knowledge, identify your strengths and weaknesses, and improve your chances of passing the exam on the first try. These D-PCM-DY-23 dumps questions cover all the topics and concepts that are essential for the D-PCM-DY-23 exam, so you can be sure that you are fully prepared. Test DELL EMC D-PCM-DY-23 free dumps below.

Page 1 of 6

1. After setting up the VoIP configuration, a network administrator issues the following commands with the results shown:

- console# show voice vlan Administrative

- Mode………………………Enable

- console# show voice vlan it gi 1/0/2

- Interface………………………………….Gi1/0/2

- Voice VLAN Interface Mode……………Enabled

- Voice VLAN ID………………………….10

- Voice VLAN COS Overwrite……………False

- Voice VLAN DSCP Value……………….46

- Voice VLAN Port Status…………………Enabled

- Voice VLAN Authentication…………….Disabled

Based on this information, what is the Layer 3 QoS value?

Gi1/0/2

2. When setting up VoIP, you decide that you want to use LLDP. LLDP is enabled by default and LLDP Transmit Management Information and Notification modes are enabled.

What additional steps need to be performed?

Enable ISDP and enable LLDP-MED confignotification

Disable ISDP and enable LLDP-MED confignotification

Enable ISDP and disable LLDP-MED confignotification

Disable ISDP and disable LLDP-MED confignotification

3. Which OSPF packet type is sent to the neighbor when LSDB difference is detected?

Hello

LSR

LSAck

LSU

4. What Dell PowerSwitch N-Series switches require QSFP28 to be used for stacking?

N3200

N1100

N2200

N1500

5. Which two functions do the preempt command configure on VRRP? (Select 2)

Enable a higher priority Backup switch to take over as Primary

Required for VRRP tracking to control which router is Primary

Enables proactive rerouting of traffic to avoid congestion

Configures the router-to-router election priority

6. A customer is upgrading the campus network Access layer switches. The upgrade requires 2x10 GbE uplinks, 48x1 GbE ports with PoE, and stacking capability of up to 12 units.

Which Dell PowerSwitch N-Series model meets the customer requirements?

N2248X-ON

N1148T-ON

N2224PX-ON

N2248PX-ON

7. Which command shows IPv6 adjacent devices on Dell OS6?

show ipv6 neighbors

show ipv6 source

show ipv6 nd

show ipv6 brief

8. A user’s workstation has an IP phone connected to a Dell EMC N-Series switch.

What is the recommended number of VLANs that should be configured on the switch port?

9. A port has been configured with port-security dynamic with one allowable MAC address.

What happens if no frames from that MAC address are seen by the switch within the MAC table age-out time?

Switch will allow the next MAC address it sees to have access on that port

No MAC addresses will be allowed access on that port

Only the original MAC address will ever be allowed on that port

All MAC addresses will be allowed access on that port

10. Which Layer 3 protocol does MLAG support?

None

Static Routing

OSPF

RIPv2

Page 2 of 6

11. What describes one of the primary functions of a VLAN?

Separate switchport interfaces

Separate the broadcast domain

Join networks together

Route to the Internet

12. 1.Which technology is designed to protect against a default gateway failure and downtime in the Dell PowerSwitch N-Series switches?

CARP

VRRP

MLAG

HSRP

13. When configuring a standard MAC ACL on a Dell EMC N-Series switch, how is the ACL filtered?

Filtered based on the Source MAC address

Filtered based on the IP protocol number

Filtered based on the Destination IP address

Filtered based on the Source IP address

14. Which configuration tool will allow a network administrator to override routing protocol decisions and determine the forwarding of packets?

SVI

SMTP

RSTP

PBR

15. When using static routes, the ip route 192.168.1.0/24 10.8.3.2 command is issued.

What does the address 10.8.3.2 specify?

Next hop IP address

Destination address

Source address

Null0

16. A network administrator wants to lock down network access using port security.

What allows an administrator to specify a list of host MAC addresses that are allowed on a port?

Static locking

Sticky mode

Switchport mode

Dynamic locking

17. Which is a valid link-local IPv6 address?

2001:db8:21aa:7:7130:a400:d167:92ab

fe80::b8b2:6397::3cfc

2001:dd71::5ece:7:6935:b407

fe80::b0d3:3911:55e2:cfc

18. What is the interaction between CDP, ISDP, and LLDP when communicating configuration information from a Dell EMC Campus networking switch to a Cisco VoIP phone?

N-Series switches can be configured to use LLDP or CDP to communicate configuration information with Cisco devices

N-Series switches can be configured to use only CDP to communicate configuration information with Cisco devices

N-Series switches can be configured to use ISDP or CDP to communicate configuration information with Cisco devices

N-Series switches can be configured to use ISDP or LLDP to communicate configuration information with Cisco devices

19. Based on the topology shown in the graphic, which ports are designated ports?

Switch A, ports Te1/0/1 and Te1/0/2

Switch B, ports Te1/0/3 and Te1/0/4

Switch B port Te1/0/3 and Switch C port Te1/0/6

Switch C, ports Te1/0/5 and Te1/0/6

20. Which command will show the policy-based routing map applied on an interface?

show ip access-lists

show route-map

show ip policy

show ip interface

Page 3 of 6

21. A core team of network administrators has been tasked with designing the upgrade to a company’s campus network. They have been instructed to adhere to the traditional campus networking model. In addition, they need to take five components into consideration; i.e., overall design, site, users, interconnect, and switch features.

What are the architectural principles aligned to switch features?

Modularity, resiliency, and static design

Modularity, resiliency, and flexibility

One size fits all, resiliency, and static design

Wireless, wired, and resiliency

22. You have been tasked with troubleshooting a LAG issue between two Dell EMC N-Series switches. The N3024-2 switch is configured correctly.

Based on the graphic, what is incorrect with the N3024-1 configuration?

N3024-1 is configured as a static port-channel

N3024-1 ports Gi1/0/7 and Gi1/0/8 are configured as voice ports

N3024-1 is configured as an LACP port-channel

N3024-1 ports Gi1/0/7 and Gi1/0/8 are configured as trunk ports

23. A network administrator is planning a PoE budget for their network.

What is the PoE source maximum power budget for a Class 4 end device?

12.95 watts

15.4 watts

34.2 watts

60 watts

24. What is the recommended maximum number of routers, per area, when using OSPF?

100

200

255

25. Which Dell OS6 command displays the IPv6 address of the default gateway and the default route associated with the gateway?

show ip route

show ipv6 route

show ip mroute

show ipv6 brief

26. What is the maximum N1100 and N1500 switches that can be stacked?

27. Based on the graphic, which command should be used on the Dell EMC N-Series Layer 2 switch to allow both client computers to receive a dynamic IP address?

Console(config)# ip redirects

Console(config)# service dhcp

Console(config)# ip helper-address 192.168.100.250

Console(config)# service-policy in dhcp_250

28. Which three statements are true about MLAG? (Select 3)

The peer-link performs the synchronization of FDB and other data.

The backup link is used to prevent split-brain scenarios.

No VLANs can be configured in the peer-link for MLAG switches.

The peer-link can let MLAG switches be in stack for additional redundancy.

User traffic may cross the peer-link for redundancy under some failure scenarios.

29. A network administrator has created an ACL to block broadcast traffic to their server on port Gi1/0/1.

Why is the ACL not functioning as desired?

ACL is not applied in the correct direction

ACLs do not support broadcast traffic

Destination address mask is incorrect

Destination IP address is incorrect

30. When configuring a PBR route-map, what are the configurable "SET" options?

set ip source, set ip next-hop, and set ip default next-hop

set ip next-hop, set ip source, and set ip precedence

set ip next-hop, set ip default next-hop, and set ip precedence

set ip source, set ip default next-hop and set ip precedence

Page 4 of 6

31. Which statement is true when connecting a PC to a VoIP phone?

Only the VoIP traffic must be part of an untagged VLAN

Only the user traffic must be part of an untagged VLAN

Both, the user and VoIP traffic must be part of an untagged VLAN

Both, the user and VoIP traffic must be part of an tagged VLAN

32. If Client B sends a packet to Client A, what is the highest level of the network hierarchy that the packet will transverse?

Distribution

Network

Access

Core

33. The exhibit represents a topology with all Dell EMC N4000 Series switches with RSTP enabled. In addition, the switches are using the default configuration on all ports and protocols.

Which port number will be blocked by spanning tree?

Te 1/0/3

Te 1/0/4

Te 1/0/5

Te 1/0/6

34. When DSCP is used for QoS prioritization, which type of service is typically used for voice traffic?

35. You need to configure OSPF on a DNOS 6 switch and have entered the following:

Switch-1(config)# ip routing -

Switch-1(config)# interface vlan 20

Switch-1(config-if-vlan20)# ip address 10.1.20.1 255.255.255.0

Switch-1(config)# router ospf -

Switch-1(config-router)# router-id 10.1.1.1

Based on the information referenced above, what is missing from the configuration?

area 0 is missing from the ip routing command

ip ospf area 0 is missing from the interface vlan 20 section

router ospf is missing the routing instance

area 0 is missing from the router-id command

36. Which command enables Virtual Router Redundancy Protocol in Global Configuration Mode on a Dell OS6 switch?

no vrrp disable

interface vrrp

vrrp enable

ip vrrp

37. How many untagged VLANs are allowed on a switchport mode trunk interface?

128

4096

38. You are configuring VRRP on a group of Dell EMC Campus networking switches. In addition to redundancy, you need to minimize any down times or disruptions on the network.

Which configuration step can be performed to help meet this requirement?

Disable VRRP preempt on only the switch configured with the highest priority

Disable VRRP preempt on all VRRP group members

Configure all VRRP group members with the same priority so they share the Master role

Increase the VRRP advertise-interval on all VRRP group members

39. What is the base configuration of an interface connected to a VoIP phone?

Voice VLAN authentication through 802.1x is enabled by default and can be disabled at a per interface level

switchport voice vlan X command on an interface allows the switch to transmit and receive traffic on VLAN X

By default, Dell EMC Campus networking switches will trust both COS and DSCP markings on traffic received from a phone

Switch ports should be configured in trunk mode to allow both data and voice traffic to ingress on separate VLANs

40. Which technologies can be implemented when configuring policy-based routing?

Policy-maps, Extended ACLs, and MAC ACLs

Policy-maps, Route-maps, and Extended ACLs

Route-maps, Extended ACLs, and MAC ACLs

Route-maps, Policy-maps, and MAC ACLs

Page 5 of 6

41. How does the weighted Queue Scheduler prioritize packets?

Scheduler prioritizes weighted queues over any strict queues

Weights are calculated based on the number of packets

Weights are used to calculate the number of bytes

Weight is assigned to each port

42. Which command enables routing in DNOS 6?

no ip routing

ip routing rip

ip routing OSPF

ip routing

43. A network administrator wants to configure an ACL to deny traffic for a specific source IP and source UDP port.

Which type of ACL should be used?

Layer 2 Standard ACL

Layer 2 Extended ACL

Layer 3 Standard ACL

Layer 3 Extended ACL

44. If the current Designated Router for the OSPF area fails, which Router ID will begin generating Type 2 LSAs?

172.16.0.93

172.16.0.92

172.16.0.94

172.16.0.95

45. What are two benefits of using remote user accounts for switch management? (Select 2)

Network administrators with individual accounts.

Accounts usable across multiple network switches.

Simplified password change management.

Accounts not dependent on other network resources.

Higher level of administrative privileges for switches.

46. Which switch port mode is recommended for ports on a Dell EMC N-Series switch with IP phones using voice VLAN?

Access

Active

Hybrid

General

47. A network administrator is setting up a Dell EMC N-Series PoE switch. The administrator is looking for a protocol that can deliver information to the end device that allows for refinement and fine tuning.

Which protocol option should be used?

Flowcontrol

dot1x

LACP

LLDP-MED

48. Why would a network administrator select MLAG for two switches versus stacking?

MLAG switches can have VLANs with both redundant and non-redundant ports.

MLAG switches have a shared management IP address.

MLAG switches can be upgraded independently from each other.

MLAG is compatible with Cisco vPC and VSS, and OS10 VL

49. Which type of an attack is considered MAC poisoning?

Duplicating the MAC address of a legitimate device so frames are forwarded to the incorrect port

Host imitating a trunk port by using tagging and trunking protocols

Flooding MAC addresses to the switch to fill its CAM table, causing the switch to act as a hub

Host on a VLAN gaining unauthorized access to other VLANs on the network

50. Standard IP access-lists are not supported on Dell PowerSwitch N-Series switches.

Which of these extended IP access-lists could be used to emulate the function of a Standard IP access-list?

ip access-list block-ACL deny 192.168.0.0 0.0.0.255 any permit every

ip access-list block-ACL deny udp 192.168.0.0 0.0.0.255 any eq 67 permit every

ip access-list block-ACL deny 192.168.0.0 0.0.0.255 192.168.0.0 0.0.0.255

ip access-list block-ACL deny udp any 192.168.0.0 0.0.0.255 eq 67 permit every

Page 6 of 6

51. Which interface on a Dell EMC N-Series switch provides the most security for management?

VLAN

Ethernet

Loopback

Out-of-band

TAGS:

D-PCM-DY-23, D-PCM-DY-23 exam dumps

Notify of

Label

Name*

Email*

Website

Label

Name*

Email*

Website

0 Comments

Oldest

Newest Most Voted

Inline Feedbacks

View all comments

Get D-PCM-DY-23 Dumps Full Version

Q&As: 168
Versions: PDF and Software Download Now

About Dumpsinfo

Dumpsinfo is a good platform providing the latest exam information and dumps questions for all IT certification exams. You can study all the latest exam dumps questions online.

[email protected]

Mon - Sat 9:00am - 6:00pm

D-PCM-DY-23 Exam Dumps – Reliable Way to Pass and Get Certified

Related

Posts

Advance Your Career by Using Online D-PSC-MN-01 Dumps

D-NWR-DY-01 Exam Dumps – Reliable Way to Pass and Get Certified

DELL EMC D-VXR-OE-23 Exam Questions Simulate Actual D-VXR-OE-23 Exam

Prepare D-SNC-DY-00 Exam with Using D-SNC-DY-00 Dump Questions

About Us

EMAIL

Services

Opening Hours