100-490 Dumps Guarantee You Pass 100-490 Exam Easily

As new threats and vulnerabilities emerge, the 100-490 exam is updated to reflect the latest trends in CCT Routing & Switching. By using 100-490 exam dumps questions, you can ensure that you're staying up-to-date with the latest exam content and are fully prepared to address new challenges in Supporting Cisco Routing and Switching Network Devices v3.0. Cisco 100-490 exam dumps questions can help you optimize your preparation and ensure that you're fully prepared for the exam. Practice free Cisco 100-490 exam dumps questions below.

Page 1 of 3

1. Which set of steps best describes how to assign a static IP address to the Ethernet port on a computer?

From the Network and Sharing Center, click Internet Protocol (TCP/IP), and follow the New Connection Wizard instructions.

From the Network and Sharing Center, click Change adapter, then double-click a local area connection. Select Internet Protocol (TCP/IP) > Properties > Use the Following Address, and then configure the IP information.

Click Start. Enter cmd and click O

Enter the IP address XX

XX

XX

XX

From the Network and Sharing Center, double-click Local Area Connection. Select Properties > iPass Protocol (IEEE 802.1x) > Properties > Static I

 Loading...

2. Which type of physical connector does a Gigabit Ethernet port typically use?

RJ-9

RJ-45

DB-25

RJ-11

 Loading...

3. How are IPv6 addresses notated?

2001:ODB8::1:1:1:1:1

2001:0DB8:130F:0000:0000:7000:0000:140B

2001:0DB8:0::

2001:0DB8::/128

 Loading...

4. Which type of memory is erased on a Cisco device when rebooted?

DRAM

PVDM

flash

NVRAM

 Loading...

5. Which two commands are valid for copying a saved configuration to RAM? (Choose two.)

copy startup-config running-config

copy running-config startup-config

copy tftp running-config

copy running-config tftp

copy tftp startup-config

 Loading...

6. Which type of memory stores the configuration of a router or switch by default?

RAM

ROM

NVRAM

flash

 Loading...

7. Which two IPv4 addresses can be assigned to a host computer? (Choose two.)

A. 255.255.255.255

B. 10.1.1.20

C. 0.0.0.0

D. 192.168.10.15

E. 292.10.3.4

 Loading...

8. Which command returns the user to the main configuration prompt from the interface configuration prompt?

end

clear

quit

exit

 Loading...

9. Which router port is used for dial-in access to the router for CLI management purposes and does not usually pass normal network traffic?

Fast Ethernet

channelized serial

AUX

Gigabit Ethernet

 Loading...

10. What are two functions of SmartJack? (Choose two.)

It regenerates the signal to compensate for signal degradation from line transmission.

It provides signal conversion.

It operates at Layer 2 of the OSI model.

It provides channel testing.

It acts as a concentration point for dial-in and dial-out connections.

 Loading...

Page 2 of 3

11. Which address facilitates the routing of packets over an IP network?

physical

transport

network

MAC

 Loading...

12. Which command initiates the copying of a Cisco IOS image to a Cisco device?

copy tftp nvram

copy tftp flash

copy flash tftp

copy xmodem flash

 Loading...

13. Which type of port on a laptop is used to connect to an Ethernet port on a Cisco switch?

DVI

RJ-11

DB-9

RJ-45

 Loading...

14. What is the fastest way to recover a software version that supports a USB flash port on a Cisco device?

tftp command

xmodem transfer command

copy command with USB memory

copy tftp flash: command

 Loading...

15. Which command provides detailed information about the components that are installed on a router, such as the model, PID, and serial number?

show chassis

show items

show inventory

show router

 Loading...

16. Refer to the exhibit.

What are two identifications for the hardware components? (Choose two.)

1 is a USB Type A port.

2 is an RJ-45 to USB Type A console cable.

2 is a USB 5-pin mini USB Type B to USB Type A console cable.

3 is a USB Type A port.

3 is a USB 5-pin mini USB Type B port.

 Loading...

17. Which bits represent the boot field in the configuration register value?

highest two bits

lowest two bits

highest four bits

lowest four bits

 Loading...

18. What are two components of a WAN connection? (Choose two.)

CSU/DSU

router

bridge

hub

switch

 Loading...

19. Which device is able to be configured as a TFTP server?

CSU/DSU

modem

Cisco router

Cisco Content Engine

 Loading...

20. Which two IPv4 addresses are assigned to host computers? (Choose two.)

292.10.3.4

10.1.1.20

255.255.255.255

0.0.0.0

192.168.10.15

 Loading...

Page 3 of 3

21. Which type of memory is used to store Cisco IOS Software permanently?

NVRAM

flash

SRAM

DRAM

 Loading...

 Loading...