CWDP-304 Dumps Questions - Effective Way to Get Certified

CWDP-304 Dumps Questions – Effective Way to Get Certified

Category:

Comments:

0 Comments

Post Date:

February 3, 2024

If you're in the field of CWNP, you know how important it is to stay up-to-date with the latest knowledge and skills to protect your organization's networks and data. One way to do that is by obtaining CWDP Certifications, specifically the CWDP-304 exam. While preparing for the CWDP-304 exam, you might consider using CWDP-304 dumps to help you familiarize yourself with the exam format and content. These CWDP-304 exam dumps questions can be an effective way to gauge your knowledge and identify areas where you may need additional study. Study online free CWDP-304 exam dumps below.

Page 1 of 8

1. Four buildings are located in a square orientation to each other. Fisch Stix Food Company is requesting a PtMP link between the buildings.

On the building with the root bridge link, what type of antenna is the best choice?

Vertically polarized omni

60° yagi

Parabolic dish

100° sector

Horizontally polarized omni

2. What document is typically created to launch a project?

Project Charter

Budget

Bill of Materials

Work Breakdown Structure

3. An engineering firm just upgraded their WLAN form nine 802.11n APS to nine 802.11ac APs. After this upgrade, they did not see any improvement in throughput.

What is the most likely cause of this result?

The APs are still using the 5 GHz lower band

The clients were not upgraded

APs are mounted on the wall

APs are transmitting at a low transmit power

4. NicoCo is building a new facility and would like to install a WLAN for primary connectivity of all clients. The requirements are dual-spectrum 802.11n supporting voice and location tracking.

What type of pre-deployment survey should be performed?

Passive, using optimized channels

Active, using a voice handset

Active, using a lowest common denominator client

Predictive

Passive, all channels

5. One of your warehouse customers called you reporting problems with their WLAN in some locations that you designed and installed over a year ago.

What should be one of your first considerations for your line of questioning?

DHCP lease exhaustion

Changes in receive gain

Inventory changes

Rogue APs from neighbors

6. Given: A WLAN controller is connected to ABC Company's core layer 3 Ethernet switch with an IEEE 802.1Q trunk connection. The WLAN controller's native VLAN is VLAN 6 and its IP address is 10.0.14.2 /24. Lightweight APs supporting centralized forwarding are connected to the network on VLANs 7, 8, and 9, and they each build a Layer 3 tunnel back to the WLAN controller's IP address. The dynamically assigned IP addresses received by each AP from a DHCP server will be ________________.

Associated with the VLAN on which they are connected.

Associated with the native VLAN of the WLAN controller.

Associated with VLAN 1, the default VLAN for new APs

Associated with a non-routable VLAN until the MAC address of the AP is removed from the controller's MAC filter

7. Using a SCA means that all APs will be using the same channel in a given layer.

How is the AP with which the client associates determined?

All APs share a virtual Multicast Address. A controller will tell the closest AP to the client to communicate with it, since it has a greater RSSI from the client.

All APs share a virtual BSSI

A controller will tell the closest AP to the client to communicate with it, since it has a greater RSSI from the client.

All APs share a virtual IP address. A controller will tell the closest AP to the client to communicate with it, since it has a greater RSSI from the client.

The client selects the AP based on a known set of MAC to BSSID mappings stored in the clients authorized SSID listing.

8. What is the purpose of Friis transmission equation [ (LdB) = 20 log(d) + 20 log (f) - 27.55 ]?

Calculate earth bulge to determine minimum antenna height

Calculate receive sensitivity for an 802.11 radio/antenna pair

Calculate RF path loss in free space

Calculate the loss experienced between the intentional radiator and antenna

9. What advantage provided by 802.11n and 802.11ac is not usable in 1X1:1 low-end client devices?

Mandatory data rates

Channel bonding

MCS data rates

Maximal Ratio Combining

10. What action should be taken after implementing a WLAN based on the design developed from the site survey process?

Post-installation survey

Requirements analysis

Gathering facility documentation

Design the infrastructure services

Page 2 of 8

11. What term refers to the security practice of obfuscating actual data from unintended receivers as the data crosses the transmission medium?

Confidentiality

Authentication

Integrity

Accounting

Nonrepudiation

12. You're about to deploy an Enterprise-class VoWLAN infrastructure. You need to ensure that QoS is properly configured throughout the network.

What Access Category (AC) should voice frames/packets use?A. AC_VI

B. AC_VO

C. AC_BE

D. AC_BK

13. When you see the SKINNY protocol in a post-install validation protocol capture, what does this indicate?

VoIP is used on the network

Multicasting is used on the network

HTTPS is in use

Secure FTP is in use

14. Given: You are evaluating the theoretical and real-world RF gain benefits of transmit and receive features introduced by 802.11 with MIMO. This exercise allows you to quantify the feature’s value in a real-world environment.

What is the maximum theoretical signal gain of chip-based TxBF and MRC (as features) when compared to the same AP using only a single antenna for transmit and receive (effectively simulating a 1x1 chip)?

2 Rx or Tx chains = 3 dBi gain3 Rx or Tx chains = approx 5 dBi gain4 Rx or Tx chains = 6 dBi gain

2 Rx or Tx chains = 1 dBi gain3 Rx or Tx chains = 2 dBi gain4 Rx or Tx chains = 3 dBi gain

2 Rx or Tx chains = 3 dBi gain3 Rx or Tx chains = 6 dBi gain4 Rx or Tx chains = 9 dBi gain

2 Rx or Tx chains = approx 4-6.5 dBi gain3 Rx or Tx chains = approx 7-10 dBi gain4 Rx or Tx chains =approx 10-12 dBi gain

15. You are being asked to design a WLAN for a number of WLAN clients that will use Telnet as the primary application. The customer has asked that you use only the number of APs necessary because of the complex installation and construction costs each AP installation will incur in this particular environment.

What design factors do you consider?

Omnidirectional antennas should be used to maximize cell overlap.

Use 11 Mbps as the lowest basic rate.

Clients could benefit from RTS/CTS mode for all transmissions.

AP transmit power should be turned down to minimize co-channel interference.

16. While configuring your site survey software for an upcoming manual survey project, you notice the configuration option for "Network Card Simulation".

What is the purpose of such a feature and when would you use it?

This setting allows the site survey software to convert the APs measured downlink RF data into a simulated data set as if the same data were transmitted by a specific client station. It is useful for determining uplink client performance when clients are located far from APs as well as projecting cell size for ad hoc networks.

Since WLAN adapters are not typically calibrated by manufacturers, this setting is a form of software calibration in which you can calibrate an (uncalibrated) adapter to match one of the calibrated adapters shown in the list. This process improves the reliability of RF data collection and reporting when uncalibrated adapters are used.

This is the configuration area in which you specify the adapter type that will be used for the site survey so that the survey software can interpret that adapters reported metrics (based on proprietary formulas) into an RF measurement that is standardized by the survey software and known to its users. This is done

17. Prior to meeting with the customer for the first time, you should do which of the following?

Decide which vendor they will benefit most from.

Research the customer as much as possible. Try to understand what their business is, who their customers are, and any other information you can find regarding product lines and recent press announcements.

Find out what vendor their competitors use.

Plan an initial design to present to them.

18. For what types of systems should you request read-only access to in order to perform an analysis of the customer’s existing infrastructure? (Choose all that apply.)

Clients

RADIUS

Switches

Active Directory

Routers

19. When troubleshooting coverage issues for a wireless network as it appears to new client associations, you should perform which type of survey?

Active survey

Passive survey

A survey is not necessary.

Predictive survey

20. What are some advantages of designing guest access with all guest users tunneled directly into the DMZ?

Allows a single SSID with different authentication/encryption models to be used for all WLAN services for corporate users and guests

Minimizes configuration requirements for segmentation and filtering of guest traffic across internal LAN

The border firewall configuration will not require any additional rules to pass guest traffic to the DMZ controller

Enhances performance of web proxy servers in the DMZ for guest Internet traffic

Page 3 of 8

21. What document should be created that provides instructions for install technicians to mount and configure APs?

Hold Harmless

Statement of Work

Bill of Materials

Physical installation guide

22. You performed a site survey with two USB Wi-Fi adapters using a special driver written for the site survey software. After deployment, you realized that the client devices used by your customer are getting lower RSSI values than that shown during your site survey.

What is the most likely reason for this result?

USB Wi-Fi adapters designed for site surveys may have better sensitivity than regular Wi-Fi cards installed in client devices.

The transmit power on the APs is higher than needed.

Regular Wi-Fi cards installed in client devices do not support the same protocols as survey adapters.

USB Wi-Fi adapters have a greater sensitivity than internal Wi-Fi adapters.

23. When performing an indoor predictive site survey to make the WLAN planning and design cycle more efficient, what is a best practice for configuration of the simulated APs in the predictive modeling software?

All simulated APs should be set to 20 MHz channels only.

Always use the default 2.2 dBi omnidirectional antenna patterns for simulated APs.

If dynamic RRM will be used, AP transmit power should be set to an estimated average level of the expected client devices, such as 25 m

Defining custom AP and antenna patterns will yield more accurate prediction data than the pre-configured vendor AP/antenna combinations.

24. In a PC-based spectrum analyzer, what data chart identifies the overall RF utilization of a specific frequency in the environment being surveyed?

FFT Max Hold

FFT Average

Swept Spectrogram

Duty cycle

25. When doing some frame capturing over the air during a voice call, you realized that frames on the downlink (from the AP to the client) direction are not being transmitted with the correct UP value for voice frames, but on the uplink (from the client to the AP) direction are being transmitted correctly.

What's the cause of this issue?

Bad client driver

AP is not receiving enough PoE, thus not using QoS features

Somewhere on the wired network QoS markings aren't being trusted

Faulty antenna on the AP

26. What limitation exists when WMM is not enabled on an 802.11n WLAN?

The maximum channel-width will be 20MHz

Only two ACs will be available

EDCA values will change

802.11 QoS will not be available

27. During a post-deployment verification, you are requested to troubleshoot an area where users are experiencing poor throughput. They are using data communication only, mainly from laptops. You captured the frame showing an incorrect FCS. This frame is typical of those that were captured by the analyzer.

What does this frame reveal about the RF network in this area?

One station seems to be streaming video, thus may have reserved significant bandwidth via admission control

Contention Free is in place in this network, which may starve some non-QoS stations from access

Multipath or excessive collisions seem to be an issue in this area

The AP seems to be too far to provide enough coverage to this area

28. When live video streaming solutions that transmit simultaneously to more than one recipient are used, what special capability should be considered and configured in all affected WLAN implementations?

IPSec

IPv6

Multicasting

Secure TCP

29. A table of VLANs in a _________ document should include what device performs ________ services. (Fill in the blanks)

HLD, routing

LLD, bridging

LLD, routing

HLD, QoS

30. Given: For this fill-in the blank question, each answer option contains an answer for the first and second blanks, separated by a dash "―". Choose the answer option that correctly fills in both blanks in the following sentence.

A WLAN may use 802.11 admission control to ________, and admission control requirements are configured separately for each ________.

Block stations with inadequate security parameters ― SSID

Identify voice-enabled wireless devices ― AP radio (that is, 2.4 GHz or 5 GHz)

Regulate the available bandwidth resources ― Access Category

Mark ingress and egress frames with priority values ― TCP/IP port

Page 4 of 8

31. An MSA commonly addresses at least which two legal categories?

Nondisclosure agreement

Hold harmless

Intellectual property protection

Indemnity clause

32. In high-density environments, such as stadiums and convention centers, what extra factor has to be taken into account that can attenuate Wi-Fi signals when these environments are having an event?

Thick walls

I-Beams

People

Fire doors

33. Using a SCA means that all APs will be using the same channel in a given layer.

How is the AP with which the client associates determined?

All APs share a virtual IP address. A controller will tell the closest AP to the client to communicate with it, since it has a greater RSSI from the client.

All APs share a virtual Multicast Address. A controller will tell the closest AP to the client to communicate with it, since it has a greater RSSI from the client.

All APs share a virtual BSSI

A controller will tell the closest AP to the client to communicate with it, since it has a greater RSSI from the client.

The client selects the AP based on a known set of MAC to BSSID mappings stored in the clients authorized SSID listing.

34. You are working on a VoWLAN design with your customer's wired networking team.

How many distinct priority levels do you expect for the voice applications?

1 priority level, but 2 queues (one for uplink traffic, one for downlink traffic)

1 priority level per client and AP pair, so the total number depends on the expected number of clients

1 priority level for voice RTP, 1 priority level for voice control and RTCP

1 priority level for VoWLAN client traffic, 1 priority level for wired VoIP client traffic

35. Which definition correctly describes the "local MAC" variation of the centralized WLAN architecture?

All MAC functions are performed by the A

A minimal subset of network control is offloaded to the WLAN controller along with management and monitoring functions.

PHY functions are performed directly by the A

MAC functions are divided almost equally between the WLAN controller and the AP, according to the time sensitivity of the feature or service.

The AP provides the RF termination point for the WLAN, but performs very few of the WLAN functions or services. The WLAN controller performs all MAC functions and the AP is very simple and lightweight.

All RF-, data-, and control-related WLAN functions are performed by the A

APs coordinate network services with one another and are managed by a WNMS,

36. After designing a WLAN infrastructure using predictive design software.

What's the best way to validate the predictive design in the physical space before deployment, if time and budget allow for it?

Deploy all of the APs as they're shown in the predictive design and perform an active site survey.

Deploy all of the APs as they're shown in the predictive design and perform a passive site survey.

Use a client device positioned where the APs will be installed and measure the signal from the client device.

Perform an AP-on-a-Stick survey using AP locations based upon the predictive design to confirm each AP's placement.

37. What two 802.11 amendments deal with regulatory and transmission requirements?

802.11k

802.11i

802.11d

802.11f

802.11h

38. A table of VLANs in a _________ document should include what device performs ________ services. (Fill in the blanks)

HLD, routing

LLD, bridging

LLD, routing

HLD, QoS

39. To increase capacity in a coverage-based wireless network, which of the following techniques are typically recommended? (Choose all that apply.)

Maximize airtime usage by disabling lower data rates.

Add additional APs and use directional antennas.

Turn up power on the access points.

Lower power on the access points and, after careful planning, add more AP

40. You are selecting external antennas for use in a bridge link deployment.

What chart should you request from the antenna vendors to make an accurate selection?

mW to dBm conversion chart

dBm to dB conversion chart

Elevation chart

Antenna coating chart

Page 5 of 8

41. When deploying long-distance 802.11 bridge links (10 miles / 16 km), what parameter may be critical for improving data flow by reducing retries caused by the long distances?

The sequence control field value

The acknowledgement timeout threshold

The minimum transmit data rate value

The CTS-to-self threshold

42. During lunch time in the break room of a company, Wi-Fi connectivity on the 2.4 GHz band is intermittent. Every other time of the day, it works fine.

What's the likely cause of this issue?

Employees are using their cell data instead of using the Wi-Fi

The AP in the cafeteria keeps rebooting due to lack of PoE budget on the switch

Toasters and ovens are heating up the air, raising the noise floor with the Wi-Fi on the 2.4 Ghz band

Microwaves in the cafeteria are interfering with the Wi-Fi on the 2.4 GHz band

43. What is a valid 40 MHz channel configuration in the 2.4 GHz ISM band where channels 1-11 are permitted?

4 (primary), +1 (secondary)

2 (primary), -1 (secondary)

8 (primary), +1 (secondary)

1 (primary), 6 (secondary)

44. Your customer is using PSK as their only authentication. They have an industry requirement to move to a stronger solution. Your recommendation is to move to a certificate-based type of authentication where both the client and server require certificates.

Which EAP type would be the best fit?

EAP-FAST

EAP-TTLS

EAP-TLS

PEAP

45. What is a radome?

A type of semi-circular ceiling found in atriums and that is a heavy cause of RF reflection.

A weatherproof piece of plastic covering an antenna or antenna system.

The unit used to measure the signal reflected backward by the end of a cable.

A piece of metal positioned behind APs mounted on outdoor poles, designed to limit the butterfly effect.

46. What is the purpose of DHCP Option 43, and how is it used with WLANs?

It provides clients with a temporary IP address on a restricted VLAN until 802.1X authentication is completed. Then the client receives its long-term IP address.

It provides IP address bindings for specific network nodes that require long-term IP address assignments. WLAN controllers are configured to use Option 43 to receive long-term IP address leases that are centrally managed with DHC

It supports vendor-specific IP address attributes for node discovery purposes. APs use Option 43 with vendor class identifiers to obtain the IP address of a centralized WLAN controller.

It integrates a DHCP server with AAA servers and user databases to dynamically assign IP addresses to client devices. During 802.1X, the AAA server uses

47. What part of the 802.11n preamble is used by the receiver to estimate the spatially multiplexed signal channel? What mode is this used in?

HT-STF in Greenfield mode only

HT-LTF in Mixed and Greenfield modes

HT-LTF in Greenfield mode only

HT-STF in Mixed and Greenfield modes

48. When performing an active site survey in an existing WLAN infrastructure, in addition to gathering throughput data, what other important function will you typically be testing at the same time?

Application filtering

Internet bandwidth

Roaming

ACL configuration

49. Which operational plane would be responsible for performing automated RF management?

Integration

Data

Distribution

Control

Management

50. During a post-validation assessment, you have configured a client for 802.1X/EAP but it is not passing authentication.

Which areas should you check in the WLAN configuration?

Whether the RADIUS server is online and configured for the matching port on the APs and WLAN controllers

Whether the RADIUS shared secret is properly configured on the supplicant and authentication server

Whether the authenticator is configured to support the EAP type(s) your client is configured for

Whether the client has a fully valid certificate

Page 6 of 8

51. When using a predictive design tool, you have selected APs with an antenna gain 3 dBi and set the transmit power of the predicted APs to 25 mW.

What should be EIRP of the APs in the design?

11 dBm

6.25 mW

125 mW

17 dBm

52. Which DHCP option, when required, should be configured and enabled to help APs locate their wireless LAN controller?

150

53. Location technology (RTLS) can use which of the following methods? (Choose all that apply.)

Sound

802.11-capable laptops

Active RFID

Infrared

UHV

UWB

Passive RFID

54. A wireless engineer from your company performed a site survey in an office building where a wireless network extension was needed. He reports that while performing a Layer 1 sweep near a meeting room full of people, he detected RF activity with a very low duty cycle. He is unsure how to interpret what he recorded to determine its impact on a future Wi-Fi network.

What is true about this RF environment and its potential impact on the WLAN?

The signal affects the entire spectrum and will render the wireless network unusable. It must be located and removed.

The signal has a low duty cycle and should not be of major impact on the wireless network.

The signal is alternating between peaks (high interference level) and valleys (low interference level). The network channel design must be built to avoid the affected peak frequencies.

The signal is typical of a high radio card background noise. It shows that the card used for the Layer 1 sweep should be replaced and the Layer 1 sweep re-

55. When implementing WLAN security according to common best practices, what feature should be enabled when configuring an EAP type?

The "Use WEP if RADIUS server unavailable" option

The "Validate server certificate" option

The "Trusted Root Certification Authorities" list

The "Do not prompt user to authorize new servers or trusted certification authorities" option

56. In a large enterprise (5000+ wireless users), by what would NOT be a recommended method by which IP addresses and VLANs are assigned to different clients associated to the same AP?

Each SSID is mapped to a static VLAN assignment

Upstream AAA servers dynamically assign VLANs to each user or group profile

Radio signal metrics (RSSI, SNR, etc.) of WLAN clients are triangulated for location-based VLAN assignment during association

Multiple VLAN pools are designated for an SSID and user IP addresses are selected in a round-robin fashion from the associated pools

57. In 802.11, clients are required to be calibrated for RSSI and SNR reporting to:

Within +/5 dB

Within +/3 dB

Within +/1 dB

Within +/0.5 dB

Within +/0.25 dB

No specific value

58. As a device starts to shift to lower PHY rates, what factors usually influence a device decision to shift to lower PHY rates? (Choose all that apply.)

Signal degradation

Packet loss

Interference

Retransmissions

59. An associated STA detects a new BSS with the same SSID as the STA's current BSS. The new BSS uses a different IP subnet than the current BSS.

If the STA is configured to use 802.1X/EAP preauthentication, what is likely to occur?

The STA will not attempt to preauthenticate because the new BSS uses a different IP subnet.

The STA will attempt to preauthenticate, but fail because the new BSS uses a different data-link broadcast domain.

The STA will attempt to preauthenticate and succeed if DHCP is supported on the new subnet.

The STA will attempt to preauthenticate and succeed if IP Mobility is enabled on the AP or WLAN controller.

60. During a validation site survey, you realize that the installers mounted some of the APs above the ceiling. They said that this was a request from the building architect due to aesthetics constraints.

During the requirements gathering, you weren't advised about any aesthetics constraints from the main stakeholder of the project.

What should you do in this case?

Remove all external antennas and use only the internal antennas to reduce multipath.

Advise the stakeholder that WLAN performance requirements will not be met and a new design process will be needed to meet the requirements.

Leave it as it is and allow automatic channel management to correct any issues.

Increase the output power on all APs by 6 dB immediately.

Page 7 of 8

61. When you see the SKINNY protocol in a post-install validation protocol capture, what does this indicate?

Secure FTP is in use

VoIP is used on the network

HTTPS is in use

Multicasting is used on the network

62. After designing a WLAN infrastructure using predictive design software.

What's the best way to validate the predictive design in the physical space before deployment, if time and budget allow for it?

Perform an AP-on-a-Stick survey using AP locations based upon the predictive design to confirm each AP's placement.

Deploy all of the APs as they're shown in the predictive design and perform a passive site survey.

Deploy all of the APs as they're shown in the predictive design and perform an active site survey.

Use a client device positioned where the APs will be installed and measure the signal from the client device.

63. What are methods of providing RF high availability?

Power APs to maximum power.

Use the HSRP/VRRP protocol.

Deploy using 100 percent overlap.

Deploy 802.3af.

Use dual spectrums.

64. You and 10 other people are connected to a public hot-spot. You issue a ping sweep on the network, but you can't find any devices on the same subnet as yours.

What feature might be enabled on the WLAN infrastructure that is preventing you from communicating with other devices on that subnet?

Peer-to-peer blocking

OSPF external routes

Band steering

Load balancing

65. When designing for a PTP outdoor link, what important consideration should be made about local vegetation? (Choose all that apply.)

Leaves

Tree height growth

Water density

Reflection factor

66. An engineering firm just upgraded their WLAN form nine 802.11n APS to nine 802.11ac APs. After this upgrade, they did not see any improvement in throughput.

What is the most likely cause of this result?

APs are transmitting at a low transmit power

The clients were not upgraded

APs are mounted on the wall

The APs are still using the 5 GHz lower band

67. When live video streaming solutions that transmit simultaneously to more than one recipient are used, what special capability should be considered and configured in all affected WLAN implementations?

Secure TCP

Multicasting

IPv6

IPSec

68. In a convention center, you have received complaints about the WLAN infrastructure. At this moment, the are only two APs in one auditorium. After analyzing the situation, you determined that there are more client devices that the infrastructure was designed for. There are only two APs to support more than 300 devices using the Wi-Fi at the same time.

What should you do to make the Wi-Fi work as expected?

Redesign the entire WLAN

Quickly add more APs

Upgrade the Ethernet connections to MultiGig

Turn up the output power on the APs so that they can handle more clients

69. When selecting a centralized WLAN architecture, what new problem may arise when you change the data forwarding model from centralized to distributed?

APs that were designed for a centralized forwarding model may not support all features in distributed forwarding mode.

The router between the APs and the controller must be made aware of the APs as forwarding client STAs.

All RRM controls will also need to be distributed to a master AP that acts as a channel and transmit power arbiter for other APs in the ES

Centralized control functions, such as key management and distribution, RRM, and load balancing will no longer be supported.

70. For what types of systems should you request read-only access to in order to perform an analysis of the customer’s existing infrastructure? (Choose all that apply.)

Clients

RADIUS

Switches

Active Directory

Routers Directory

Routers

Page 8 of 8

71. ABC Manufacturing has a heavily-used dual-band (2.4 / 5 GHz) WLAN, but sporadic RF interference across the 2.4 GHz band is causing dropped VoWiFi calls and leading to data connectivity and throughput problems.

In addition to avoiding 2.4 GHz channels and installing a distributed spectrum analyzer to locate RF interference sources, what should the implementer do to resolve the problem fully?

Have only guest access on the 5 GHz channels.

Move all corporate data clients and VoWiFi devices to the 5 GHz channels appropriate for their regulatory domain.

Use captive portals for guest authentication in 5 GHz.

Implement WPA-PSK everywhere in the network.

72. For what purpose is SSID hiding generally useful? (Choose all that apply.)

Preventing guests from attempting to join the secured corporate network

Obscuring the network name from potential attackers

Minimizing help desk calls from users and guests attempting to join the wrong network

Preventing legitimate corporate users from finding the guest network

73. As an implementation engineer, you have just received initial design specs from a network designer for your dual-band 802.11n deployment.

The network design documents prescribe the following data rate configuration for the 2.4 GHz radio:

- Basic Rates 5.5, 6, 11, 12 Mbps

- Supported Rates 9, 18, 24, 36, 48, and 54 Mbps as well as MCS 0-15

What will result from this design strategy?

By disabling support for 1 and 2 Mbps while allowing 5.5 and 11 Mbps, the network will force 802.11b clients to use these higher data rates.

Protection mechanisms will always be in use on this network to support 5.5 and 11 Mbps as basic rates.

HR/DSSS (802.11b) stations will not be able to associate to the service set.

This configuration violates the IEEE specification that defines 6, 12, and 24 Mbps as mandatory data rates for 802.11g/n.

74. In an RSN requiring low-latency reassociations and no fast secure roaming protocols, what security solutions are ideal for protecting VoWiFi communication? (Choose all that apply.)

WPA2-Personal

WPA-Personal

WPA2-Enterprise

802.1X/EAP

WEP

802.1X/EAP

75. An enterprise customer is subject to the highest standards for network uptime.

When designing their wireless network, you should consider which of the following? (Choose all that apply)

The failover of the wireless network only

The failover of the wired network only

The failover of the wireless and wired network

The physical aspects such as power and cabling

TAGS:

CWDP-304, CWDP-304 exam dumps

Notify of

Label

Name*

Email*

Website

Label

Name*

Email*

Website

0 Comments

Oldest

Newest Most Voted

Inline Feedbacks

View all comments

Get CWDP-304 Dumps Full Version

Q&As: 251
Versions: PDF and Software Download Now

About Dumpsinfo

Dumpsinfo is a good platform providing the latest exam information and dumps questions for all IT certification exams. You can study all the latest exam dumps questions online.

[email protected]

Mon - Sat 9:00am - 6:00pm

CWDP-304 Dumps Questions – Effective Way to Get Certified

Related

Posts

Prepare CWT-101 Exam with Using CWT-101 Dump Questions

Good CWSP-207 Exam Dumps Save Your Preparation Time

CWNA-109 Dumps Help You Study Objectives

About Us

EMAIL

Services

Opening Hours