JN0-363 Dumps Guarantee You Pass JN0-363 Exam Easily

As new threats and vulnerabilities emerge, the JN0-363 exam is updated to reflect the latest trends in JNCIS-SP. By using JN0-363 exam dumps questions, you can ensure that you're staying up-to-date with the latest exam content and are fully prepared to address new challenges in Service Provider Routing and Switching, Specialist (JNCIS-SP). Juniper JN0-363 exam dumps questions can help you optimize your preparation and ensure that you're fully prepared for the exam. Practice free Juniper JN0-363 exam dumps questions below.

Page 1 of 2

1. Exhibit





Routers R1 and R4 have a VRRP priority of 90, while R2 and R3 have default VRRP priorities

Referring to the exhibit, which router will be elected as the primary VRRP router?

R3

R4

R2

R1

 Loading...

2. Exhibit





Which two statements are correct about the service provider MPLS network shown in the exhibit? (Choose two.)

R3 is considered a P router.

R3 is considered a PE router.

R3 is considered a transit router.

R3 is considered an ingress router.

 Loading...

3. Exhibit





Referring to the exhibit, which two statements are correct? (Choose two.)

The OSPF Interfaces are configured as point-to-point.

The ge-0/0' 1. 0 Interface is configured as passive.

The R2 device is an AB

Junos OS default OSPF hello timers and dead intervals are used on all interfaces.

 Loading...

4. Exhibit





You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.

What is the problem in this scenario?

This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

The family iso statement must be added to the logical interface.

The router at the other end of the link Is not sending any IS-IS Hello messages.

The router at the other end of the link is a Level 1 only router.

 Loading...

5. Which two statements ate correct about the community BGP attribute on a Junos device? (Choose two.)

The community attribute is a mandatory BGP attribute.

If the community attribute is present, it is ignored and deleted in the BGP updates.

If the community attribute is present, it should be passed unchanged in the BGP updates.

The community attribute is an optional BGP attribute.

 Loading...

6. Exhibit





You have configured graceful RE switchover (GRES), however you cannot complete the show system switchover command.

Referring to the exhibit, what is the problem?

The command is only available if non-stop routing is enabled.

The command is only available on the backup Routing Engine.

The command is only available If a backup router is configured.

The command is only available If graceful restart is enabled.

 Loading...

7. Exhibit





Referring to the exhibit, what must be included in the Route1 configuration when establishing an EBGP session with the ISP?

A local address must be specified.

A local AS must be specified.

The BGP session type internal must be specified.

The BGP session type external must be specified.

 Loading...

8. What are two types of SlDs used in segment touting? (Choose two.)

node

adjacency

link

interface

 Loading...

9. Which two interface types are used as tunnel endpoints? (Choose two.)

ae

ip

ge

gr

 Loading...

10. The segment touting SRGB start label Is 10,000 and the SRGB index range is 500.

In this scenario, which two statements are correct? (Choose two.)

The first usable label is 10,00 1.

The last usable label is 10.50 1.

The last usable label is 10,499.

The first usable label Is 10,000.

 Loading...

Page 2 of 2

11. You have created a routing instance named vr3 that will provide access to Server 2 (10.0.0.2) (or the hosts on the 10.10.10.0/24 network .

Which command would you use to test connectivity between vr3 and Server 2?

user@vr3> ping 10.0.0.2 count 5

user@vr3> ping 10.0.0.2 count 5 source 10.10.10.1

user9router1> ping 10.0.0.2 count 5

user@router1> ping 10.0.0.2 routing-instance vr3 count 5

 Loading...

12. Exhibit





Referring to the exhibit, which statement is true about VRRP?

VRRP communication between the two devices is not functioning correctly.

Both routers are in the same state because they have the same VRRP priority.

RRP Is functioning normally in active/active mode.

The routers should use different virtual IP addresses for VRRP to function correctly.

 Loading...

13. What are two bridging concepts that are used to maintain an Ethernet switching table? (Choose two.)

learning

exporting

aging

timing

 Loading...

14. Exhibit





You have an established LSP between your R1 and R5 devices using the configuration shown in the exhibit. You are asked to ensure that MPLS labels are used to forward traffic by all devices within the LSP.

Which action will accomplish this behavior?

Configure the ultimace-hop-popping statement under the R1_TO_R5 label switched path on R 1.

Configure the explicit-null statement under the protocol mpls hierarchy on R 1.

Delete the no-espf statement under the R1_TO_R5 label switched path on R 1.

Configure the install statement under the R1_TO_R5 label switched path on R 1.

 Loading...

15. You are bringing a new network online with three IS-IS routers using default Junos election priorities. The routers are configured as Level 2 only IS-IS routers .

Which statement is true about the DIS election in this scenario?

The router with the highest MAC address will be elected as the DI

The router with the highest numerical lo0 IP address will be elected as the DI

The router with the lowest numerical lo0 IP address will be elected as the DI

The router with the lowest MAC address will be elected as the DI

 Loading...

16. Exhibit





Referring to the exhibit, which two statements are correct? (Choose two.)

Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0/1 unchanged.

Traffic ingressing ge-0/0/0 that is tagged will VLAN 100 will be dropped.

Traffic ingressing ge0/0/0 that Is tagged with VLAN 200 will egress ge-0/0/1 with an outer VLAN tag of 200.

Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0M with an outer VLAN tag of 200.

 Loading...

17. Which two statements are correct about the way that BGP propagates routes by default? (Choose two.)

A route learned by EBGP will be re-advertised to IBGP peers.

A route learned by IBGP will not be re-advertised lo IBGP peers.

A route learned by EBGP will not be re-advertised to IBGP peers.

A route learned by IBGP will be re-advertised to IBGP peers.

 Loading...

 Loading...