JN0-480 Exam Dumps – Reliable Way to Pass and Get Certified

If you are looking for a reliable and comprehensive way to prepare for your JN0-480 certification exam, look no further than JN0-480 exam questions. These JN0-480 exam dumps questions are designed to help you assess your knowledge, identify your strengths and weaknesses, and improve your chances of passing the exam on the first try. These JN0-480 dumps questions cover all the topics and concepts that are essential for the JN0-480 exam, so you can be sure that you are fully prepared. Test Juniper JN0-480 free dumps below.

Page 1 of 2

1. You are adding a new switch to Juniper Apstra software. The Managed Devices page shows the "0 OS-Quarantined" status.

What is the proper next step to make the device ready for use in a blueprint?

Acknowledge the device.

Take the device out of maintenance mode.

Install the agent for the device.

Take the device out of drain state.

 Loading...

2. You must configure a static route for traffic to exit a configured routing zone. In the Juniper Apstra Ul. where would you accomplish this task?

under Active -> Virtual -> Routing Zones

under Staged -> Virtual -> Routing Zones

under Active -> Connectivity Templates

under Staged -> Connectivity Templates

 Loading...

3. Exhibit.





Referring to the exhibit, how many tack types ate used in the staged blueprint?

six

three

seven

two

 Loading...

4. Exhibit.





Referring to the exhibit, what needs to change in the IP fabric to make it a valid IP fabric?

A. The IP fabric must consist of only one device model throughout the fabric.

B. The connection between the two spine nodes must be increased to 40 Gbps.

C. The IP fabric connections must be increased to a speed greater than 10 Gbps.

D. The connection between the two spine nodes must be removed.

 Loading...

5. In the case of IP Clos data center five-stage fabric design, what are two rotes of the super spines? (Choose two.)

Super spines are used to interconnect two different data center pods.

Super spines connect to all spine devices within the five-stage architecture.

Super spines are used to connect leaf nodes within a data center pod.

Super spines are always connected to an external data center gateway.

 Loading...

6. Which attribute enables Juniper Apstra to scale and manage thousands of devices with a single server instance?

A. Apstra is installed as a cloud resource.

B. Apstra is based on NGINX.

C. Apstra is available as an OVA.

D. Apstra is a distributed state system.

 Loading...

7. You want to keep virtual networks isolated from each other within the Juniper Apstra system.

In this scenario, what are three ways to accomplish this task? (Choose three.)

Disable IPv4 connectivity when creating the virtual network within the same Routing Zone.

Enable Security Policy for virtual networks in the same Routing Zone.

Disable Route Target exports when creating the Routing Zones.

Use Connectivity Templates to block access within the same Routing Zone.

Put each network in different Routing Zones.

 Loading...

8. Which two statements are correct regarding a pristine configuration in Juniper Apstra? (Choose two.)

It is the configuration file placed on the device when decommissioning the device.

It is the device's currently active configuration.

It Is the configuration file on a device before acknowledgment in Apstra.

It is the device's previously active configuration.

 Loading...

9. Exhibit.





Referring to the exhibit, how do you display the IPv6 subnets lot all of the listed VXLANs?

IPv6 subnets ate shown when each VXLAN is selected individually.

Select Columns, then select IPv6 Subnet.

Select all VXLANs. and the IPv6 Subnets column will appear

An IPv6 Subnets column is not shown, indicating that no VXLAN has an assigned IPv6 subnet

 Loading...

10. You want to apply a configlet to a specific device using Juniper Apstra.

Which two parameters would be used to accomplish this task? (Choose two.)

form factor

hostname

port group

tags

 Loading...

Page 2 of 2

11. Which two actions are required during Juniper Apstra's deploy phase? (Choose two.)

Assign device profiles to the blueprint.

Assign user roles to the blueprint.

Assign interlace maps to the blueprint.

Assign resources to the blueprint.

 Loading...

12. Exhibit.





Which two statements ate correct about the graph query output shown in the exhibit? (Choose two.)

The interface has an IP address assigned to it.

The output shows a LAG connection.

The switch in the output is a Juniper device.

The interface has tags assigned to it.

 Loading...

13. Using the Juniper Apstra multitenancy capabilities, which approach will allow a tenant to interconnect two different routing zones?

Interconnection is the default behavior.

Use interconnection through the fabric spine nodes.

Interconnection cannot be enabled.

Use interconnection through an external gateway.

 Loading...

14. A member of your organization made changes to a predefined interface map using Juniper Apstra.

Which two statements are correct in this scenario? (Choose two.)

Changes to interface maps in the global catalog do not affect interface maps that have already been imported into blueprint catalogs

Any changes made to predefined interface maps are discarded when Apstra is upgraded.

Changes made to predefined interface maps will not have an impact on the Apstra software.

Changes to interface maps in the global catalog will raise anomalies that may need to be addressed at the next commit.

 Loading...

15. Which fabric type should be chosen in a template to create a five-stage Clos?

collapsed

circuit switched

rack-based

pod-based

 Loading...

16. Juniper Apstra has indicated an anomaly with respect to cabling.

What are two ways to remediate the issue? (Choose two.)

Manually edit the cabling map.

Redeploy the errant device.

Set the invalid ports to a disabled state.

Have Apstra autoremediate the cabling map using LLD

 Loading...

17. Exhibit.





Referring to the exhibit, what is the minimum information you must add to create a new routing zone?

VRF Name only

VRF Name and Routing policies

VRF Name, VLAN I

And VNI

VRF Name, VLAN ID, VNI, Routing Policies

 Loading...

18. You are receiving cable, interface, and BGP anomalies from several devices within the data center fabric.

In Juniper Apstra. how would you troubleshoot these types of errors?

In the Ul, go to Time Voyager and revert to the last working version.

In the Ul, access the console to the devices and review the interface states.

In the Ul, go to Devices and confirm that agent connectivity is fine.

In the Ul, verify device connectivity by consulting the cable map.

 Loading...

19. What is the purpose of a Juniper Apstra rack?

It stores information on how pods connect to super spines.

It stores information on how leaf nodes connect to generic devices

It stores IP address and ASN pool information.

It stores device port data rates and vendor information.

 Loading...

20. You want to add a configuration that is not supported by Juniper Apstra reference architecture using a configlet.

Which two configurations would be applicable in this scenario? (Choose two.)

static route configuration

policy configuration

syslog configuration

NTP configuration

 Loading...

 Loading...