Online JN0-105 Dumps Help You Understand Questions Well

If you're interested in pursuing the JNCIA-Junos certification, it's important to understand the exam format and the types of questions you can expect. This is where JN0-105 questions come in. JN0-105 exam dumps questions are designed to simulate the actual certification exam, providing you with a deeper understanding of the exam format and what to expect on test day. By taking practice exams and reviewing JN0-105 questions, you can identify areas where you may need to focus your studying. Study free JN0-105 exam dumps below.

Page 1 of 2

1. You issue the telnet 10.10.10.1 source 192.168.100.1 command.

Which two statements are correct in this scenario? (Choose two.)

The telnet session will have a source address of 10.10.10.1.

The telnet session will have a destination address of 192.168.100.1.

The telnet session will have a destination address of 10.10.10.1.

The telnet session will have a source address of 192.168.100.1.

 Loading...

2. Which two addresses are included in an Ethernet frame header? (Choose two.)

source IP address

source MAC address

destination IP address

destination MAC address

 Loading...

3. An administrator configures a router's interface with an IPv4 address and subnet mask. The administrator also confirms that this interface is in an up state.

In this scenario, which two route types are created on the local router? (Choose two.)

a static route

a local route

a dynamic route

a direct route

 Loading...

4. Exhibit

policy-options {policy-statement Load-Balance-Policy {term Load-Balance {then {load-balance per- flow; accept;

}

}

}

}

routing-options {

router-id 192.168.100.11; autonomous-system 65201; forwarding-table {

export Load-Balance-Policy;

Referring to the exhibit, which two statements are correct? (Choose two.)

The policy enables equal cost load balancing in the forwarding table.

The policy must be applied under the protocols hierarchy.

The policy enables per-packet load balancing.

The policy enables flow-based load balancing.

 Loading...

5. You have just increased the MTU size of interface ge-0/0/0 and committed the configuration.

Which command would help you identify the applied MTU change?

monitor interface ge-0/0/0

monitor traffic interface ge-0/0/0

show interfaces ge-0/0/0 terse

show interfaces ge-0/0/0

 Loading...

6. You are creating a new policy to accept and redistribute routes into your IGP.

In this scenario, which match criteria would you use to identify the route prefixes to select?

instance

route-type

neighbor

route-filter

 Loading...

7. You are trying to diagnose packet loss at interface ge-0/0/3.

In this scenario, which command would help you view error statistics in real time?

show interface terse

show interface ge-0/0/3

monitor interface traffic

monitor interface ge-0/0/3

 Loading...

8. Which service does RADIUS provide?

routing

authentication

DNS resolution

time synchronization

 Loading...

9. Which two common routing policy actions affect the flow of policy evaluation? (Choose two.)

next policy

community

next term

next hop

 Loading...

10. Exhibit.





Referring to the exhibit, which routing configuration is required for these two users to access the remote server?

Users must connect directly to the router.

Users and the server require a default gateway.

Trunk ports must be enabled on the switch.

A routing protocol must be enabled on the router.

 Loading...

Page 2 of 2

11. Which two statements are true about the Junos OS? (Choose two.)

Routing tables are stored in the control plane.

Exception traffic is never sent to the control plane.

Exception traffic is sent to the control plane.

Routing tables are stored in the forwarding plane.

 Loading...

12. What will the request system configuration rescue save command do?

It saves the most recently committed configuration as the rescue configuration.

It saves the candidate configuration as the rescue configuration.

It saves a configuration version prior to the configuration most recently committed as the rescue configuration.

It activates the rescue configuration.

 Loading...

13. Which two actions happen when multiple users issue the configure exclusive command to enter configuration mode on a Junos device? (Choose two.)

Other users can enter configuration mode.

The candidate configuration is unlocked.

Other users cannot enter configuration mode.

The candidate configuration is locked.

 Loading...

14. Which statement is correct when multiple users are configuring a Junos device using the configure private command?

A commit by any user will commit changes made by all active users.

A commit will not succeed until there is only a single user in configuration mode.

Each user gets their own candidate configuration.

Each user shares the same candidate configuration.

 Loading...

15. Exhibit

[edit system archival] user@router# show configuration {

transfer-on-commit; archive-sites {

"scp://[email protected] : /archive" password ## SECRET-DATA

"ftp://[email protected]:/archive" password "$9..."; ## SECRET-DATA.

Referring to the exhibit, where are the configuration backup files stored?

Files are stored to the SCP site and the FTP site in a round-robin manner.

Files are stored to the SCP site and the FTP site simultaneously.

Files are stored to any site as selected by Junos internally.

Files are stored to the SCP site but if the transfer fails, then to the FTP site.

 Loading...

16. + apply-groups-except Don't inherit configuration data from these groups

{hold:node0}[edit]

root#

You are unable to remotely access your Juniper device using the CLI.

Referring to the exhibit, which command would you add to the existing configuration to enable remote CLI access?

load factory-default

set system root-authentication plain-text-password

set system services ssh

set system login idle-timeout 20

 Loading...

17. Exhibit

user@router> show route 192.168.100.2

inet.O: 15 destinations, 17 routes (15 active, 0 holddown, 0 hidden) Limit/Threshold:

1048576/1048576 destinations

+ = Active Route, - = Last Active, * = Both 192.168.100.2/32 *[OSPF/IO] 00:14:29, metric 1

> to 172.16.1.6 via ge-0/0/1.0 [BGP/170] 00:06:49, localpref 100

AS path: 65102 I, validation-state: unverified > to 172.16.1.6 via ge-0/0/1.0

Referring to the exhibit, which statement is correct?

The BGP path is the only active route.

The BGP route is preferred over the OSPF route.

The OSPF path is the only active route.

/ Traffic is load-balanced across two routes.

 Loading...

18. When considering routing tables and forwarding tables, which two statements are correct? (Choose two.)

The routing table is used by the RE to select the best route.

The forwarding table stores all routes and prefixes from all protocols.

The forwarding table is used by the RE to select the best route.

The routing table stores all routes and prefixes from all protocols.

 Loading...

19. What information does the forwarding table require so that the device forwards traffic? (Choose three.)

OSPF metric value

next hop IP address

BGP local preference value

outgoing interface name

next hop MAC address

 Loading...

 Loading...