Test Online JN0-104 Dumps Questions to Be Certified

Category:

Comments:

0 Comments

Post Date:

August 4, 2023

To help prepare for the JN0-104 exam, you may want to consider using JN0-104 exam dumps questions. These questions are designed to test your knowledge and understanding of the topics covered on the exam. The more you practice answering JN0-104 dumps questions, the more comfortable you will become with the exam format and the types of questions you can expect to see. JN0-104 dumps can help reduce anxiety on exam day and improve your chances of success. Go and test free JN0-104 exam dumps questions here.

Page 1 of 5

1. Which statement about the show chassis hardware Command is correct?

The command provides a list of installed hardware components, including serial numbers and model numbers.

The command provides a list of all current hardware utilization statistics and operational status

The command provides 2 list of supported hardware components and their current operating status

The command provides a list of supported hardware components and environmental thresholds.

2. Click the Exhibit button

Referring to the exhibit, you are unable to reach devices in the 172.19.25.0/28 subnet.

What should you do to solve this problem?

Enable the ge-0/0/2 interface.

Enable the ge-0/0/2.2 interface.

Enable the ge-0/0/2.0 interface.

Enable the ge-0/0/2.1 interface.

3. A device receives a route update for network 172.19.0.0/16 from two different routing information sources.

In this scenario, which parameter will determine the active route?

the route learned from the next hop with the highest IP address

the route learned with the lowest default route preference

the route learned from the next hop with the lowest IP address

the route with the lowest metric

4. Referring to the exhibit.

Which OSPF feature would connect Area 2 to Area 0?

route summarization

equal-cost multipath

virtual link

database synchronization

5. After logging in as root, you enter the cl i command.

What does this command do?

It enables you to enter configuration mode.

It enables you to enter line edit mode.

It enables you to enter operational mode.

It enables you to enter interface mode.

6. Click the Exhibit button.

You have applied the policy shown in the exhibit as an import policy to your BGP group.

In this scenario, what will happen when the router receives the 192.168.30.48/32 route?

It will be sent to the default BGP policy

It wall match term-1 and be accepted.

It wall match term-2 and be accepted

It will match term-2 and be rejected.

7. Which two statements about the Junos OS are true? (Choose two.)

It uses a different software source code base for each platform.

It supports Java for automation on all platforms.

It supports XML for automation on all platforms.

It uses the same software source code base for all platforms.

8. What are two characteristics of UDP? (Choose two.)

UDP is connection-oriented.

UDP packets are sent best-effort.

UDP is more reliable than TC

UDP operates at the transport layer.

9. Click the Exhibit button

A packet destined to the 172.27. 102.65 IP address is received by the ge-0/0/1.0 interface on your Junos device. The input firewall filter shown in the exhibit is applied to the ge-0/0/1.0 interface.

Which two actions are performed in this scenario? (Choose two.)

The packet is logged

The packet is accepted

The packet is counted

The packet is discarded.

10. Click the Exhibit button.

The next hop identified in the static route command is not directly connected to your router.

Referring to the exhibit, what must be added to the command for the static route to work?

retain

resolve

readvertise

install

Page 2 of 5

11. What are three characteristics of Layer 2 switches? (Choose Three)

Layer 2 switches separates multicast domains.

Layer 2 switches separates collision domains.

Layer 2 switches forward traffic addressed to hosts that reside on the same collision domain.

Layer 2 switches forward traffic addressed to hosts that reside on a different collision domain.

Layer 2 switches forward broadcast traffic.

12. Which protocol is responsible for learning an IPv6 neighbor's IMAC address?

Neighbor Discovery Protocol (NDP)

Media Access Control Security (MACsec)

Address Resolution Protocol (ARP)

Network Address Translation (NAT)

13. Which component is responsible for performing protocol updates and system management?

forwarding tables

Routing Engine

bridging table

Packet Forwarding Engine

14. What will the help syslog UI_DBASE_LOGOUT_EVENT command show you?

It will show you the options you can use with sysiog UI_DBASE_LOGOUT_EVENT

It will show you only UI_DBASE_LOGOUT_EVENT messages in the system log

It will only show you syslog messages without UI_DBASE_LOGOUT_EVENT

It will describe the UI_DBASE_LOGOUT_EVENT message code

15. Click the Exhibit button.

Which operational mode command in Junos OS produces the output shown in the exhibit?

show system users

show system connections

show system commit

show system reboot

16. Which two ping command parameters would be used to troubleshoot MTU issues? (Choose two.)

ping do-not-fragment

ping rapid

ping verbose

ping size

17. Click the Exhibit button.

Referring to the exhibit, a firewall filter is configured and applied to the ge-0/0/1 interface.

In this scenario, which statement is correct?

All traffic to destination 10.10.10.0/24 is accepted.

All traffic entering on interface ge-0/0/1 is discarded.

All traffic entering on interface ge-0/0/1 is accepted.

All traffic from source 10.10.10.0/24 is accepted.

18. Which statement about the forwarding table is correct?

It contains all known routes including IPv6-

It is only available on the PFE

It is only available on the RE

It is available on both the RE and the PF

19. For the interface ge-1/2/3.4, what does "ge" represent?

SONET/SDH

Gigabit Ethernet C Aggregated Ethernet

GRE

20. Exhibit:

[edit routing-options]

user@router# show

static {

route 0.0.0.0/0 {

next-hop 10.1.1.1;

qualified-next-hop 10.1.1.254 {

preference 4;

}

}

}

Assuming both paths shown in the exhibit are available, which statement is correct?

Traffic matching the default route will use 172.16.1.1 as the next hop

Traffic matching the default route will use 172.16.1.254 as the next hop

Traffic matching the default route will be load-balanced per flow across both next hops

Traffic matching the default route will be load-balanced per packet across both next hops.

Page 3 of 5

21. Which two statements about exception traffic processing are correct? (Choose two.)

When congestion occurs, only exception traffic is given preference.

By default, a rate-limiter for exception traffic exists on the internal link between the control plane and the forwarding plane

When congestion occurs, local and control traffic are given preference.

By default, no rate-limiter for exception traffic exists on the internal link between the control plane and the forwarding plane.

22. Click the Exhibit button.

You want to make the OSPF route shown in the exhibit the active route for the 10.10.10.0/24 IP address.

Which action is required to accomplish this task?

Set the static route to no-readvertise.

Set the OSPF route preference to 4.

Set the static route preference to 0

Set the OSPF metric to 0

23. Which set of IP addresses are in the same subnet?

185.114.16.91/28 and 185.114.16.96/28

185.114.16.77/28 and 185.114.16.82/28

185.114.16.40/28 and 185.114.16.45/28

185.114.16.59/28 and 185.114.16.82/28

24. What are two link state routing protocols? (Choose two.)

IS-IS

OSPF

IBGP

EBGP

25. What is the network ID address of the IPv4 subnet that includes the IP address 114.180.192.120/28?

114.180.192.118/28

114.180.192.100/28

114.180.192.112/28

114.180.192.106/28

26. Click the Exhibit button

Referring to the exhibit, which two statements are correct? (Choose two.)

All other traffic from the Web destined to 172.19.20.50 is accepted.

All other traffic from the Web destined to 172.19.20.50 is discarded

The HTTP traffic destined to 172.19.20.50 is accepted.

The HTTP traffic from source 172.19.20.50 is accepted.

27. In the show I compare rollback 49 command, what is the purpose of the I?

The | is a shortcut to redirect output from a command line to a file.

The filters the output of the show command.

The | is used to represent an "either or” statement.

The | changes the command from an operational command to a configuration mode command.

28. You must configure the 2bfc:0000:0000:beef:0217:cbff:0000:5c85 IPv6 address on your device.

In this scenario, which three addresses are correct? (Choose three.)

2bfc::beef:217:cbff:0:5c85

2bfc:0:0:beef:0217:cbff:0:5c85

2BFCnBEEF:0217:CBFF:0:5C85

2bfc:0:beef:0217:cbff:0:5c85

2BFC::BEEF:217:CBFF::5C85

29. Which command allows you to execute operational mode commands while in configuration mode?

activate

show

run

set

30. Click the Exhibit button

You are connecting to a new device in your network and are presented with the information and prompt shown in the exhibit.

Which three steps must be carried out to edit the configuration on this device? (Choose three.)

Type configure at the > prompt.

Type cli at the = prompt

Type cli at the > prompt

Page 4 of 5

31. 1.You enable unicast reverse path forwarding on the ge-0/0/1.0 interface A packet is received on the ge-0/0/1.0 interface with a source address of 10.10.10.10. A route lookup determines that the next hop for the 10.10.10.10 address is the ge-0/0/1.0 interface. In this scenario which action is performed?

The packet is logged

The packet is forwarded

The packet is rejected

The packet is discarded

32. You are creating a route filter that will match the network address of 192.168.64.0/24 In this scenario, which configuration statement will accomplish this task?

from route-filter 192.168.32.0/24 longer

from route-filter 152.168.128.0/24 orlonger

from route-filter 192.168.64.0/24 longer

from route-filter 192.168.64.0/24 orlonger

33. Your Junos OS routers use a static route to provide connectivity to the management network. You do not want this static route to be redistributed using a dynamic routing protocol.

In this scenario, which static route configuration parameter will accomplish this task?

no-install

no-retain

no-resolve

no-readvertise

34. Which statement regarding transit traffic processing is correct?

Transit traffic is processed by both the control plane and forwarding plane.

Transit traffic is only processed by the control plane.

Transit traffic is only processed by the forwarding plane

Transit traffic is not processed by the local device.

35. What are two important steps when upgrading an SRX300 Series device? (Choose two.)

Verify that enough space exists to upload the software package.

Clear all alarms.

Reboot the device.

Verify that the NETCONF protocol is enabled.

36. You are asked to configure a Junos device to perform regular configuration backups

Which feature will you configure under the [edit system) hierarchy to accomplish this task?

archival

backup-router

syslog

tracing

37. Which two statements about the configure exclusive command are correct? (Choose two.)

The command excludes other users from editing the configuration.

The command retains all uncommitted changes when exiting exclusive mode

The command causes the loss of all uncommitted changes when exiting exclusive mode

The command allows multiple users to edit private copies of the configuration concurrently.

38. Click the Exhibit button.

Click the Exhibit button.

Referring to the exhibit, which statement is correct about traffic received on the ge-0/0/1.0 interface?

All traffic will be silently dropped.

All traffic will be accepted.

All traffic will be dropped and a UDP message sent back to the source.

All traffic will be dropped and an ICMP notification sent back to the source.

39. Data Packet Flow Control

To control the flow of data packets transiting the device as the packets are being forwarded from a source to a destination, you can apply stateless firewall filters to the input or output of the router’s or switch’s physical interfaces.

…”

[edit]

user@router#

In which mode is the system currently operating, as shown in the exhibit?

operational mode

UNIX shell

configuration mode

single-user mode

40. What are three valid software release designations for the junos OS? (Choose three.)

Page 5 of 5

41. Which command causes the Junos OS to temporarily activate a configuration?

commit and-quite

commit synchronize

commit check

commit confirmed

42. Which command allows multiple users to edit a configuration while conning only their unique changes?

configure exclusive

configure batch

configure private

configure dynamic

43. Which attribute must be defined when configunng a non-root user in Junos OS?

class

uid

authentication

full-name

TAGS:

JN0-104, JN0-104 exam dumps

Notify of

Label

Name*

Email*

Website

Label

Name*

Email*

Website

0 Comments

Oldest

Newest Most Voted

Inline Feedbacks

View all comments

Get JN0-104 Dumps Full Version

Q&As: 142
Versions: PDF and Software Download Now

About Dumpsinfo

Dumpsinfo is a good platform providing the latest exam information and dumps questions for all IT certification exams. You can study all the latest exam dumps questions online.

[email protected]

Mon - Sat 9:00am - 6:00pm

Test Online JN0-104 Dumps Questions to Be Certified

Related

Posts

Study Online JN0-637 Exam Dumps to Pass

Valid JN0-252 Exam Dumps are Your best Choice to Pass

JN0-280 Dumps Questions – Effective Way to Get Certified

Online JN0-105 Dumps Help You Understand Questions Well

About Us

EMAIL

Services

Opening Hours